rFactor 2 Online Tools by Chris “redapg”

Discussion in 'Modding' started by Slow Motion, Oct 11, 2016.

  1. Emery

    Emery Registered

    Joined:
    Oct 24, 2010
    Messages:
    3,035
    Likes Received:
    1,654
    In the tire sizing tool, does width refer to tread width or section width?

    upload_2022-8-2_17-11-34.png
     
  2. redapg

    redapg Registered

    Joined:
    Jan 16, 2012
    Messages:
    3,959
    Likes Received:
    2,809
    That is a good Question.
    It usually should use the Tread Width, where the Tire Wall meets the Tread.
    But i have checked it now and it uses the overall Width.
    I did make some Editing in the Past, especially because of the switch from php 5 to 7 and i maybe made something wrong there.
    I'll have to recheck that and also the other 2 Tire Resize Scripts and fix them if necessary.
    While i'll do it, i will deactivate the 3 Scripts and iform you here, when they are online again.
     
    Emery likes this.
  3. redapg

    redapg Registered

    Joined:
    Jan 16, 2012
    Messages:
    3,959
    Likes Received:
    2,809
    The 3 Tire Resize Tools are online again, i had to modify 2 of them, to get them using the Tread instead of the whole Width again.
    Thanks @Emery for reporting the Problem.
     
    Emery and philrob like this.
  4. Emery

    Emery Registered

    Joined:
    Oct 24, 2010
    Messages:
    3,035
    Likes Received:
    1,654
    LOL because I didn't even know there was a problem, merely knew I couldn't tell which was right (glad it's the tread width). Thanks very much for all you've done with these tools!
     
    redapg likes this.
  5. Mauro

    Mauro Registered

    Joined:
    Oct 14, 2011
    Messages:
    2,128
    Likes Received:
    3,973
    i updated rf2 to latest build, but now when i open a car in devmod "easy icon creator showroom" i have this error message:

    [​IMG]

    any solutions?
     
  6. redapg

    redapg Registered

    Joined:
    Jan 16, 2012
    Messages:
    3,959
    Likes Received:
    2,809
    Yes, hit "Enter". ;)
    No seriously now ..... i will fix that quickly.
     
  7. Mauro

    Mauro Registered

    Joined:
    Oct 14, 2011
    Messages:
    2,128
    Likes Received:
    3,973
    tried it
    but i have to hit "cancel" :) and it works
    if i select ok, each time i open a new car in showroom i have that error message

    p.s. and tk again for your work
     
    redapg likes this.
  8. redapg

    redapg Registered

    Joined:
    Jan 16, 2012
    Messages:
    3,959
    Likes Received:
    2,809
    Thanks for using it. :)

    The Showroom is fixed, no LodOut Error anymore.
    Please download again and overwrite the old Files.
     
    Emery, RoWo and Mauro like this.
  9. yoss

    yoss Registered

    Joined:
    Nov 4, 2010
    Messages:
    1,021
    Likes Received:
    2,700
  10. redapg

    redapg Registered

    Joined:
    Jan 16, 2012
    Messages:
    3,959
    Likes Received:
    2,809
    I can not reproduce that Problem and i have no .htaccess File in use.
    Did you try it with another Browser and/or empty the Browser Cache?
    Does it also happen with other Tools from my Site?

    EDIT
    PS When i click on the Link to your Website (https://www.apex-modding.com/), in your Apex User Signature, Firefox doesn't want to load your Site and says that it has a potential Risk, to steel Data or betray in any Way.
     
    Last edited: Sep 9, 2022
  11. yoss

    yoss Registered

    Joined:
    Nov 4, 2010
    Messages:
    1,021
    Likes Received:
    2,700
  12. redapg

    redapg Registered

    Joined:
    Jan 16, 2012
    Messages:
    3,959
    Likes Received:
    2,809
    Hello Franck,
    i just used that Link this Morning, to again check the Firefox Message, to tell you what it is about and that Message still appeared, when i did use the Address https://www.apex-modding.com/
    But if i click Ignore and Continue, i also get that File not Found Message.
    So everything is OK. :)
    Maybe it's just the wrong Certificate that is still connected with/present at that Address and that doesn't matches the Website Address.
    Chris
     
  13. redapg

    redapg Registered

    Joined:
    Jan 16, 2012
    Messages:
    3,959
    Likes Received:
    2,809
    Due to the Warnings:
    RF2 Warning : XYZ.GMT has default LOD Out of 10,000m, please consider optimization.
    that you almost always get in DevMode now, when a Track gets loaded, i have written a new small Script, with that you can add LodOut Tag Entries for the affected Meshes, into the SCN File.
    It is called Add LodOut Values for Meshes into a Track SCN File
    As always, if Problems appear, please report here. :)
     
    philrob, Javibeza, lagg and 1 other person like this.
  14. philrob

    philrob Registered

    Joined:
    Jan 12, 2012
    Messages:
    572
    Likes Received:
    1,204
    Thanks for this Chris, it can become very long winded fixing this error.
     
    redapg likes this.
  15. redapg

    redapg Registered

    Joined:
    Jan 16, 2012
    Messages:
    3,959
    Likes Received:
    2,809
    I have to apologize. :oops:
    I have forgotten some Lines, that "translate" the Option, to keep the original Setting into nothing.
    Now you get (in the english Version) LodOut=(keep original LodOut)
    And i fear the Game can not handle that. :D
    So the Tool is offline until i have fixed that. ;)
     
  16. redapg

    redapg Registered

    Joined:
    Jan 16, 2012
    Messages:
    3,959
    Likes Received:
    2,809
    The Tool is online again and should work properly now.
     
    Corti, FuNK!, philrob and 1 other person like this.
  17. redapg

    redapg Registered

    Joined:
    Jan 16, 2012
    Messages:
    3,959
    Likes Received:
    2,809
    I did add the Option, to set a LodOut Value of 9999, to thisTool:
    Add LodOut Values for Meshes into a Track SCN File
    that is not really different from 10000, but it avoids to get the Warning Message in DevMode and can be used for Objects, that need a big LodOut Value, like Horizons for Example.
    And i also added a Hint about it.
     
    Last edited: Sep 21, 2022
    Corti, RoWo and lagg like this.
  18. philrob

    philrob Registered

    Joined:
    Jan 12, 2012
    Messages:
    572
    Likes Received:
    1,204
    Chris,
    when i use the Lod tool i have a small problem:

    This is the original from Montjuich

    Instance=montlamp01
    {
    VisGroups=(32)
    MeshFile=montlamp01.gmt CollTarget=False HATTarget=False LODOut=(10000.0)
    }

    and this is the updated version from the tool, i set the Lod to 2500

    Instance=montlamp01
    {
    VisGroups=(32)
    MeshFile=MONTLAMP01.GMT LodOut=(2500) CollTarget=False HATTarget=False LODOut=(10000.0)

    am i missing something about removing the existing LODOut=(10000.0) ?

    is it something in the formatting of the Instance line ?
     
    redapg likes this.
  19. redapg

    redapg Registered

    Joined:
    Jan 16, 2012
    Messages:
    3,959
    Likes Received:
    2,809
    That's funny. :)
    When i wrote the Tool, i thought "what, if the uploaded SCN already has LodOut Entries?"
    But then i thought, no, SCN Files normally don't have LodOut Entries.
    And now you exactly post about that. :D

    I will add something that will fix that.
     
    Corti likes this.
  20. philrob

    philrob Registered

    Joined:
    Jan 12, 2012
    Messages:
    572
    Likes Received:
    1,204
    Thank you. i didnt think about that.Simed adds Lodouts to its output.
     
    Corti and redapg like this.

Share This Page